Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub

Suggested Site

Listed here down the page yow will discover more awesome details in relation to How to Install a Bathtub.


How to Install a Bathtub Yourself
Mounting a bath tub isn't exactly brain surgery, yet it does require strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably hard project. If the old tub is easily easily accessible, the project can relocate rapidly; if you have to open a wall to eliminate the old bathtub and also position the brand-new bathtub, the task is a lot harder. In either situation, the task is within a residence handyman's skills, although you will need an assistant to leave the old bathtub as well as set in the brand-new one. See to it you have actually certified on your own for the task as well as are comfortable trying it. Rather than employing a service provider to take over a halfway-completed project, it is better to take into consideration utilizing one prior to you start. Chances are you may require a professional plumber to make tube connections.
This write-up will certainly help you install a new tub in your shower room if you have currently gotten a brand-new tub as well as don't need to transform the plan of your previous water supply pipes.
Your devices and material list must consist of the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Removing Old Taps


    If you require to replace old taps with new ones as a part of your setup, then the first thing you ought to do is disconnect the water system. After doing so, activate the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be quite bothersome due to the restricted gain access to that is commonly the instance.
    Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric all set for the staying water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will need to be cleaned of any old securing substance.
    Prior to going on to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.

    Suitable New Taps


    If the tails of the new taps are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a link to the current supply pipelines.
    If you require to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines are in area in between the tap as well as the sink. Protect the faucet in position with the producer supplied backnut. When the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous kind ought to be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.

    Setting up the Tub


    Using the two wood boards under its feet, place the tub in the needed position. The wood boards are handy in uniformly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four small factors.
    The following objective is to make sure that the tub is leveled all round. This can be accomplished by examining the level and readjusting the feet on the bathtub till the level reviews level.
    To set up taps, fit all-time low of the furthest adaptable faucet adapter to the proper supply pipe by making a compression sign up with; after that do the very same for the various other tap.
    Switch on the water system and also inspect all joints as well as new pipework for leakages and also tighten them if essential. Fill the bath tub as well as likewise inspect the overflow electrical outlet and also the normal electrical outlet for leaks.
    Ultimately, fix the bath paneling as described in the supplier's user's manual. Tiling and also sealing around the bathtub must wait until the bathtub has actually been made use of a minimum of once as this will certainly resolve it into its last placement.

    Planning for the Setup


    To start with, the supporting frame supplied with the bathroom must be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to prevent stress on the bath tub.
    Fit the versatile tap adapters to the bottom of both faucets making use of 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you utilize every one of the provided washers.
    Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its last position.

    Tiling Around the Bath tub


    In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, leading to issues with moisture and also possible leakages to the ceiling listed below.
    You can pick from a range of coloured sealants to blend in your fixtures and fittings. They are offered in tubes and also cartridges, and are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to enable the activity experienced when the tub is in use. The sealant can fracture fairly very early if you do not take into account this movement before sealing.
    Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise conveniently offered on the market. It is recommended to fit the floor tiles using water-resistant or waterproof glue and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    We hope you enjoyed reading our part on Installing A Bathtub. Thanks a lot for taking a few minutes to read our blog post. Kindly set aside a second to distribute this page if you enjoyed it. I recognize the value of reading our article about Tools You Need to Install a New Bathtub .


    Guaranteed satisfaction offered.

    Leave a Reply

    Your email address will not be published. Required fields are marked *